HRC FL

STOCK ITEM
Flanged type, long block with and without ball chain. HRC55FL is without ball chain.

For high load applications or any application where severe chock-loads may occur, the standard version offers better safety margins by its higher static limit (C0). For light to medium loads where a very long lifetime is required, the ball-cage will show superior life span and reliability.

Please note that ball chain versions must never be used for linear speeds exceeding 3 m/s!

Size 20 – 55 delivered with angled standard nipple.

Lubrications injections ports on the block:
N1: Front of the block. All blocks are delivered with front mounted standard grease nipple.
N2: Side of the block. The side lubrication injection port is sealed on delivery to prevent leakage of lubrication.
N3: Top of the block with an O-ring seal. The top lubrication injection port is sealed on delivery to prevent leakage of lubrication.

Dimensions in mm.

Lead times in the table below are only indications. Choice of preload, accuracy class and other options will affect lead time. Please contact us for exact delivery time for your request.

For more information about calculation of life, load rating and static moment see Technical information.
Read more
Designation Select all CAD Compare Get quote Lead Time * Remark Dynamic Load Capacity C (N) Static Load Capacity C0 (N) Static Moment Mp0 (Nm) Static Moment Mr0 (Nm) Static Moment My0 (Nm) Dynamic Moment Mr (Nm) Dynamic Moment Mp (Nm) Dynamic Moment My (Nm) Weight Block (g)
Get quote 1 - 20400 38500 390 415 390 220 207 207 504
Get quote 1 - 30700 57700 710 735 710 391 378 378 870
Get quote 1 - 39600 70200 950 1105 950 623 536 536 1385
Get quote 2 - 54700 106500 1755 2185 1755 1122 901 901 2000
Get quote 1 - 89500 169100 3460 4430 3460 2345 1831 1831 4280
Get quote 1 No ball chain 147000 226000 5284 6472 5284 4210 3437 3437 6963

*Green: Normally in stock, contact us for current status. Blue: Contact us for delivery time.

Designation Select all CAD Compare Get quote L H W L1 H1 h2 W1 W2 S1 S2 S3 S4 E T N1 N2 N3 M x g2 M1 D x d x g1 P1 P2 Hole Pitch (P)
Get quote 87.2 30 63 70.2 20 25 20 21.5 6 9.4 18.1 18.8 10 10 M3x7.5 M3x5.5 P4 M6x10 M5 9.5 x 6 x 8.5 40 53 60
Get quote 105 36 70 86 23 30 23 23.5 8 12.3 23.5 24.5 12 16 M6x7.5 M3x6.5 P4 M8x12 M6 11 x 7 x 9 45 57 60
Get quote 118 42 90 94 27 35.2 28 31 8 12 25.7 25.8 12 12 M6x8.5 M6x5 P5 M10x15 M8 14 x 9 x 12 52 72 80
Get quote 136.6 48 100 111.6 32 40.4 34 33 7.5 15 30.1 30.8 12 16 M6x10 M6x7 P5 M10x15 M8 14 x 9 x 12 62 82 80
Get quote 171.5 60 120 138.5 39 50.7 45 37.5 11.1 18.1 35 35 14 19 PTI/8x12.5 M6x10.5 P5 M12x18 M10 20 x 14 x 17 80 100 105
Get quote 202 70 140 160 45.7 58 53 43.5 13.5 23.5 41.5 40.5 12 18 M6x10 M6x13 P5 M14x18 M12 24 x 16 x 20 95 116 120
  • STOCK ITEM

    HRC MN

    Slim – standard length – standard height
  • STOCK ITEM

    HRC ML

    Slim – long – standard height
  • STOCK ITEM

    ERC MN

    Slim – standard length – low height
  • STOCK ITEM

    HRC FN

    Flanged – standard length – standard height (most common)
  • STOCK ITEM
  • STOCK ITEM

    ARC MN

    Slim – standard length – low height
  • STOCK ITEM
  • STOCK ITEM

    ARC FS

    Flanged – short – low height
  • STOCK ITEM

    ARC FN

    Flanged – standard length – low height